Versatile Engine Management Systems / / ACMV, LLC
  Top » Catalog » Engine Management » Accessories » LM1815.4024 My Account  |  Cart Contents  |  Checkout   
Categories
Engine Management-> (158)
  Adapter cables (12)
  Fuel delivery (8)
  iButton security (2)
  Ignition (5)
  Pneumatic parts (6)
  Sensors (27)
  Universal Harness (3)
  Connectors (16)
  Accessories (7)
  Wiring Accessories (13)
  Upgrade Parts-> (13)
  Spare Parts-> (35)
Manufacturers
What's New? more

USB soundcard
9.97EUR
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
Information
Shipping & Returns
Privacy Notice
Ether Cryptocurrency
Bitcoin Cryptocurrency
Conditions of Use
Contact Us
VR to HALL
[LM1815.4024]
17.32EUR

Originally ment for VR wheelspeed sensor to 0/5V wheelspeed (frequency) input.
When ordered "VR to HALL without divider" in the order comment => no internal soldering needed for "divby1" output: can be useful between VR engine position sensor and ECU with HALL input. (but not the other way around !)

An (LM1815) VR to HALL interface and a (HC4024 or HEF4024) counter(divider) chip in a small DSUB9 connector housing.

  • Requires 5V supply (from the assembled v3 controller EC36/28 pin, or other source, only appr. 10mA needed)
  • The LM1815 (adaptive hysteresys threshold VR interface chip, the adaptive input mode can be configured in 3 modes with simple solder-blob) output is available, normally low level, outputs 1 short (less than 100 usec) high-pulse at the negative-going zero crossing edge of the input pin. Useful for using VR (crankpos, campos or wheelspeed) sensors when the ECU (or other device) is equipped with HALL signal input.
  • The output of LM1815 goes to 4024 counter / frequency divider. This divided output (divby8) is useful for ABS wheels that have more than 10 pulses per wheel rotation. The reset input signal of the 4024 is available on the DSUB9 pinout (can be used as prohibit signal to reset the counter, keep output low). Normally the divided output is only useful for wheelspeed signal, not for crank or cam position. However for bench-testing PC soundcard => VR to HALL => divider => v3 with HALL type input configured to "coil-type" none-missing tooth trigger can be useful to enable testing at lower RPM where the given soundcard would be otherwise problematic, noisy (because of internal high-pass filter).

All outputs are 0/5V, like "HALL" or optical sensor signals. Divider options: (divby4 and divby8 are wired via PCB trace to DSUB9 pin). See the pinout on the included paper (divby1, divby4 and divby8 are all available on DSUB9, no solderblob or internal soldering needed on the new version), previously:
  • divby8 selectable with solderblob (default)
  • divby4 selectable with solderblob
  • divby2 only available on the 4024 chip, not selectable with solderblob (not recommended)
  • To get HALL signal without dividing, (on the old version) one needs to solder a wire from LM1815pin12 (solder to the resistor, the trace goes to the 4024 divider chip) to the DSUB9. Because of the short pulses, the "without divider" signal is NOT suitable FOR WHEELSPEED. Only useful for primary or secondary or third trigger (when one wants to use VR sensor with an ECU - v3 or possibly other type ordered with HALL input),

If ECU has very strong input pullup on the HALL input (lower than 3kOhm resistance: when measured DC voltage is >1.25V with the HALL input pulled down to GND with a 1 kOhm resistor) , mention that in the order comment, just in case (if necessary, install a 2k7 or 2k4 pulldown resistor, between GND and HALL input, which is same as output of VR to HALL ).
Paper with pinout included.

This product was added to our catalog on Friday 06 May, 2011.
Reviews
Customers who bought this product also purchased
ECU VEMS V3 internal CAN
ECU VEMS V3 internal CAN
VEMS motronic88
VEMS motronic88
VEMS motronic55
VEMS motronic55

STM32F103/MCP2515
Bluetooth-RS232 adapter (no USB)
Bluetooth-RS232 adapter (no USB)
revirgin6/3
revirgin6/3
Shopping Cart more
0 items
Manufacturer Info
VEMS Group Homepage
Other products
Notifications more
NotificationsNotify me of updates to VR to HALL
Tell A Friend
 
Tell someone you know about this product.
Reviews more
Write ReviewWrite a review on this product!
Languages
English Deutsch
Currencies

Copyright © 2017 VEMS Shop
Powered by osCommerce