Versatile Engine Management Systems / / ACMV, LLC
  Startseite » Katalog » Engine Management » Sensors » bare Ihr Konto  |  Warenkorb  |  Kasse   
Engine Management-> (157)
  Adapter cables (12)
  iButton security (2)
  Ignition (5)
  Kraftstoffanlieferung (6)
  Pneumatic parts (7)
  Sensors (27)
  Universal Harness (3)
  Connectors (16)
  Accessories (7)
  Wiring Accessories (13)
  -> (13)
  -> (35)
Neue Produkte Zeige mehr

Brass Nipple M10x1
Verwenden Sie Stichworte, um ein Produkt zu finden.
erweiterte Suche
Liefer- und

 und Datenschutz

Ether Cryptocurrency
Bitcoin Cryptocurrency
Unsere AGB's
Bare MAP sensor

Bare (unpackaged) Absolute Pressure (MAP) sensor.
When looking into the sensor small tube and legs point to the right (as on the image) Pin1 is the bottom pin .
Comes without packaging. Recommended for fitting inside the ECM case (eg. Alubos).

  • The 5V version is useful. Choose the 5V supply..
  • The 12V supply will NOT work if mounted on the mainboard ! This option is very uncommon, and not recommended unless you know what you are doing.12V only works if you wire accordingly. Might be useful if you place outside the box (but than the packaged sensor is better). Also, you need to install transient suppression and fuse for overvoltage protection.

Sensor nipple:
  • OD=3mm for the 5/3mm tube. For this, you likely want some 5/3mm tube, and VIV type pneumatic connector (VIV5353 or VIV6453: that is 5/3mm on one end and 5/3mm or 6/4mm on the other end). The force required to pull off the 5/3mm tube from the sensor nipple is tiny, so it must be secured mechanically to prevent accidental come-off. The saw-tooth nipple is much safer.
  • with saw-toothed nipple: for 6/4mm pneumatic tube or rubber hose (make sure the rubber wall is thick enough, it should not collapse from vacuum)

  1. : pressure signal out (via 1k protection resistor. Find this)
  2. : GND (also available on pin 5 as you can see)
  3. : +5V (regulated) supply (appr 6mA supply current)
  4. : optional: SMD 0805 NTC (eg. 100k with 100k pullup) also possible onboard - eg. for board temp (NOT for IAT / MAT)
  5. : GND (also available on pin 2)
  6. : optional +12..15V supply input (for +12V supply option). Not connected for (the normal) 5v supply option.

Small 6 pin L shaped pinheader included (so it can be mounted on genboard v3.x perpendicularly to the mainboard). Write "preferrably no pinheader for bare MAP sensor" in the order comment if you want to use wires and mount some other way.

MAP connection:
Pressure range:
Dieses Produkt haben wir am Donnerstag, 25. Juni 2009 in unseren Katalog aufgenommen.
Kunden, die dieses Produkt gekauft haben, haben auch folgende Produkte gekauft:
LED - superbright 5mm
LED - superbright 5mm

Brass Nipple M10x1
small switchover 20A relay
small switchover 20A relay
Molded Serial Cable
Molded Serial Cable

Bluetooth-RS232 adapter (no USB)
Bluetooth-RS232 adapter (no USB)
Warenkorb Zeige mehr
1 x Differential Pressure sensor
1 x 250kPa MAP sensor/bare
Benachrichtigungen Zeige mehr
BenachrichtigungenBenachrichtigen Sie mich über Aktuelles zu diesem Artikel Bare MAP sensor
Empfehlen Sie diesen Artikel einfach per eMail weiter.
Bewertungen Zeige mehr
Bewertung schreibenBewerten Sie dieses Produkt!
English Deutsch

Copyright © 2018 VEMS Shop
Powered by osCommerce