Versatile Engine Management Systems / / ACMV, LLC
  Startseite » Katalog » Engine Management » v3.6 Ihr Konto  |  Warenkorb  |  Kasse   
Kategorien
Engine Management-> (157)
  Adapter cables (12)
  iButton security (2)
  Ignition (5)
  Kraftstoffanlieferung (8)
  Pneumatic parts (6)
  Sensors (27)
  Universal Harness (3)
  Connectors (16)
  Accessories (7)
  Wiring Accessories (13)
  -> (13)
  -> (34)
Hersteller
Neue Produkte Zeige mehr

Brass Nipple 1/8NPT
5.70EUR
Schnellsuche
 
Verwenden Sie Stichworte, um ein Produkt zu finden.
erweiterte Suche
Informationen
Liefer- und
 Versandkosten

Privatsphäre
 und Datenschutz

Ether Cryptocurrency
Bitcoin Cryptocurrency
Unsere AGB's
Kontakt
ECU VEMS V3
[v3.6]
496.40EUR

Assembled, cased VEMS v3

Our leading product with a very strong feature set. Has the ability to control the smallest of engines to the largest you may want to build. Key Features

  • Sequential Control of up to 8 banks of injectors
  • Built in transistorised coil igniters for up to 8 coils
  • Built in Wideband controller
  • Turbo friendly features such as Exhaust Gas Temperature, Anti-lag, and boost control
  • Configurable control of low and high current drivers for lights, relays and solenoids, including up to 4 solenoids for VVTI / VANOS / Camshaft-angle control (optional: 4 Hi-Side PFET drivers eg. for BMW S54)
  • Field upgradable software
  • High Quality Case and Sealed Connectors
  • Datalogging via serial connection or optional SD card interface
  • Advanced Idle Air Control
  • Motorsport / experts: Interface for ETC BridgeOutputdriver useful for electronic (drive-by-wire) throttle.
VEMS utilizes an advanced RISC microprocessor and surface mounted component technology, with state of the art electronics to allow you to precisely control your engine. Ask your regional VEMS dealer for more information VEMS is manufactured in the E.U. Sensors VEMS can be configured to use almost any standard OEM sensor for:
  • Throttle position
  • Coolant temperature
  • Air temperature
  • Crank and Cam sensors - configurable for the standard OEM configurations such as Ford 36-1, GM/Bosch 60-2, Audi 5 cylinder 135 tooth as well as being customizable for many different timing strategies
  • Manifold Pressure through a choice of built-in pressure sensors, or an external OEM type
  • External fuel and exhaust pressures
Additionally VEMS also has the built in ability to control:
  • Integrated Wideband O2 Controller utilizing the low cost Bosch LSU4 sensor
  • Up to 2 Exhaust Gas Temperature sensors
Drivers/Outputs Throughout the development of VEMS, Customization has been the focus. The number of driver channels are as plentiful as the ways of configuring their operation. Outputs can be triggered by temperature, RPM, throttle position, or air pressure. 6 Low current drivers providing control for relays (fuel pump, fan, water pump) or lights (shift light, activation light, MIL) 8 High Current solenoid drivers that can be configured to control:
  • Fuel Injectors
  • Variable cam timing solenoids (VANOS, VTEC, VVT etc)
  • Idle air controllers
  • Nitrous solenoids
  • Boost controllers
VEMS features an advanced injector control system, which can control high impedence injectors with incredible precision. Coil drivers are built in and can be specified when purchasing a unit, up to 8 ignition coil drivers can be fitted, which can be configured to run single coils, wasted spark coil packs or Coil On Plugs. Because the coil control is built in VEMS has full control with coil charge/dwell times
  • 8: all 8 ignition channels are configured with built-in ignition driver controlling the ground of a coil. This is recommended for 8 cyl fully sequential (non-wasted-spark) ignition with traditional coils. Also popular for 5 cyl setups and 6cyl COP install.
  • 6+2: 6 IGBT + 2 logic-level : Suitable for up to 12cyl wasted spark, up to 6 cyl fully sequential ignition, while also suitable for the 4cyl active wasted spark modules
  • 4+4: 4 IGBT + 4 logic-level output
  • 2+6: 2 IGBT + 6 logic-level output
  • 0: 0 IGBT + 8 logic-level output (useful for 8cyl fully sequential with active coils)

Flyback:
  • "active flyback" is a must for low-Z injectors (universal: can be used for high-Z too)
  • or "High-Z only 30V flyback" for high-Z injectors only.
  • Low-Voltage is obsolete (not recommended, except for those who know exactly what they are doing, or replacement of old ECU with similar option if re-tuning VE is not an option.

Hi side 4 PFETs:
  • If no "ETC bridgeoutput interface" then Hi-side outputs are p259/4,5,6,7 (EC36/pin3,15,31,30)
  • If "ETC bridgeoutput interface">0 then Hi-side outputs are from the bridge ( controlled by p259/2,3,4,5 via the flying loom SSC connector - please configure one at a time in VT as MISC2 output, toggle "inverted" and verify by measurement ; the relevant EC36 outputs are low-current low-side switches )

Specify the engine model (which does not, by itself, make it a "special request", and it is non-binding; but allows some chance of catching mis-specification early). Special request Examples:
  • BMW S54 dual-VANOS engine: VR, HALL, HALL + 4 * PFET high-side switches for the 4 hydraulic cam-actuator solenoids
  • BMW S50 or S52 dual-VANOS engine: VR, VR, VR + 4 * PFET high-side switches for the 4 hydraulic cam-actuator solenoids.
  • Do NOT write misleading information in the order comment. Eg. if you write just "BMW S50" we assume VR,VR,VR + 4 PFETs needed; If S50 engine is modified (eg. camsensor donated from M50 ) specifying S50 is misleading without further details (preferrably on wiki page)
  • "Preferrably leave 2 (or N...) custom (mcp3208) analog inputs without internal pullup resistor" (most analog inputs, by default, are equipped with internal pullup to +5V for installer convenience, but some sensors, like most pressure sensors are easier to install withOUT internal pullup).

Service=ASAP orders are handled in different queue (which only makes sense together with expedited delivery, if payment is received, and special instructions - if any - are crystal-clear: if writing order comment, try to be very precise using references to shop products, nomenclature, exact precise terms to avoid uncertainty, especially for an ASAP order). Service=slow can be very slow, takes 3 or more weeks longer than ASAP. Only choose slow if specs is known months in advance (or ordering generic ECU in advance).
To connect the ECU to the application, you may also be interested in:

HINT: choose 300kPa or 400kPa (6/4 or simplenipple) MAP sensor; and select your primary trigger VR/HALL (and secondary also, if special). Choose less than 8 ignition drivers if logiclevel outputs needed for active igncoils. The other options: if you don't know which you need => choose the default.

Optionen:
1-wire interface:
EGT input:
ETC BridgeOutput_Interface:
Flyback:
Hi-side PFET outputs:
ignition driver:
Knock input channels:
LCD connection:
MAP connection:
mounting-style:
primary_trigger:
secondary_trigger:
Service:
Special requests:
withSDcard:
Für weitere Informationen, besuchen Sie bitte die Homepage zu diesem Produkt.
Dieses Produkt haben wir am Donnerstag, 18. März 2004 in unseren Katalog aufgenommen.
Bewertungen
Kunden, die dieses Produkt gekauft haben, haben auch folgende Produkte gekauft:

STM32F103/MCP2515
revirgin6/3
revirgin6/3
Bluetooth-RS232 adapter (no USB)
Bluetooth-RS232 adapter (no USB)
Molded Serial Cable
Molded Serial Cable
Ethanol Sensor Connector
Ethanol Sensor Connector
small switchover 20A relay
small switchover 20A relay
Warenkorb Zeige mehr
1 x Boost MAP and MAT
1 x Payment Coupon
49.80EUR
Hersteller Info
Mehr Produkte
Benachrichtigungen Zeige mehr
BenachrichtigungenBenachrichtigen Sie mich über Aktuelles zu diesem Artikel ECU VEMS V3
Weiterempfehlen
 
Empfehlen Sie diesen Artikel einfach per eMail weiter.
Bewertungen Zeige mehr
Bewertung schreibenBewerten Sie dieses Produkt!
Sprachen
English Deutsch
Währungen

Copyright © 2017 VEMS Shop
Powered by osCommerce